Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Coordinated slide and pan motion from the eMotimo Rotator; use the PTZ camera’s own controls for its other axes
• Physical inputs for every eMotimo axis of control
• Tune live-control speed and feel for each axis, map axes to the preferred inputs, and reverse direction when needed
• Maestro automatically discovers eMotimo controllers on the same network
• Set and recall 30 timed, cinematic presets
• Set and run 8 timed, cinematic loops
• Power-on positioning gets the system ready within five minutes of startup. Saved presets and loops load automatically, so operators do not have to recreate their shots each time they power on.
• Switch between connected camera rigs from Maestro’s touchscreen or built-in Stream Deck keys
• Wall power for Conductor SA2.6 and the PTZ camera

What do you need from eMotimo?

• Maestro Network Controller
• Conductor SA2.6 + RigWheels Passport/RailDolly Integration + Rotator
• Riser with Clamp and 100 mm Arca Plate (recommended for mounting the PTZ camera)

What else do you need from a third party?

• RigWheels Passport/RailDolly with track
• PTZ camera of your choice
• Ethernet cabling and a network connection for Maestro and Conductor SA2.6
• Wall power for Conductor SA2.6 and the PTZ camera (Conductor AC adapter included with the bundle; use the camera’s compatible AC supply)

Steps to program:

1. Power on Conductor SA2.6 and Maestro on the same network. Maestro discovers the controller automatically.
2. Select the rig on Maestro. Use its physical inputs to frame the shot and adjust axis mapping, speed, and feel.
3. Save the start and end positions as timed presets.
4. Create a loop between those presets and set its move timing.
5. Start and stop the loop from Maestro’s built-in Stream Deck keys.

At the next startup, power-on positioning restores the saved setup and gets the rig ready within five minutes.

Features:

• Position the PTZ camera remotely or run a ping-pong AutoDolly loop
• eMotimo Rotator pans in coordination with slide to maintain framing in a loop (AutoPan)
• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Cinematic Studio Ready
  • Live control
  • Set and recall 30 timed, cinematic presets
  • Set and recall 8 timed, cinematic loops (ping-pong)
  • Control over a wired network with Bitfocus Companion or locally with the included gaming controller
• Wall power for Conductor SA2.6 and the PTZ camera

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration + Rotator
• Riser with Clamp and 100mm Arca Plate (recommended for mounting PTZ to eMotimo Rotator)
  • Riser with Clamp
  • 100mm Arca Plate

What else do you need from a third party?

• RigWheels Passport 2 with track
• PTZ camera of your choice
• Computer with Bitfocus Companion installed
• Elgato Stream Deck XL (recommended for Bitfocus Companion)
• Wall power for Conductor SA2.6 and the PTZ camera (Conductor AC adapter included with the bundle; use the camera’s compatible AC supply)

Steps to program:

1. Power on Conductor SA2.6 and connect the computer running Bitfocus Companion to the same wired network.
2. Configure the eMotimo connection and assign live-control, preset, and loop actions through the Stream Deck.
3. Use Companion to frame two positions and set a preset at each one.
4. Use Companion’s loop actions to select those presets as the endpoints and set the move timing.
5. Start and stop the loop through the connected Stream Deck.

For network controller configuration, see the Bitfocus Companion setup guide.

For network controller configuration, see the Skaarhoj setup guide.

Features:

• Position the camera remotely or run a ping-pong AutoDolly loop
• eMotimo Rotator pans in coordination with slide to maintain framing in a loop (AutoPan)
• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Cinematic Studio Ready
  • Live control
  • Set and recall 30 timed, cinematic presets
  • Set and recall 8 timed, cinematic loops (ping-pong)
  • Control over a wired network with Bitfocus Companion or locally with the included gaming controller
• Battery or AC operation
• Supports camera payloads up to 30 lb
• Powers and controls Tilta Nucleus-M and Nucleus-M II FIZ motors

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration + Rotator

What else do you need from a third party?

• RigWheels Passport 2 with track
  
• Flat base tripod head with 3/8"-16 mounting hole
• Two Tilta Nucleus-M or Nucleus-M II motors and the required cables
• V-Mount or Gold Mount battery with D-Tap output for battery operation or AC power solution for Conductor SA2.6 and PTZ
• Computer with Bitfocus Companion installed
• Elgato Stream Deck XL (recommended for Bitfocus Companion)

Steps to program:

1. Power on Conductor SA2.6 and connect the computer running Bitfocus Companion to the same wired network.
2. Configure the eMotimo connection and assign live-control, preset, and loop actions through the Stream Deck.
3. Use Companion to frame two positions and set a preset at each one.
4. Use Companion’s loop actions to select those presets as the endpoints and set the move timing.
5. Start and stop the loop through the connected Stream Deck.

For network controller configuration, see the Bitfocus Companion setup guide.

Features:

• Position the camera remotely or run a ping-pong AutoDolly loop
• eMotimo Rotator pans in coordination with slide to maintain framing in a loop (AutoPan)
• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Cinematic Studio Ready
  • Live control
  • Set and recall 30 timed, cinematic presets
  • Set and recall 8 timed, cinematic loops (ping-pong)
  • Control over a wired network with Skaarhoj or locally with the included gaming controller
• Battery or AC operation
• Supports camera payloads up to 30 lb
• Powers and controls Tilta Nucleus-M and Nucleus-M II FIZ motors

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration + Rotator

What else do you need from a third party?

• RigWheels Passport 2 with track
• Flat base tripod head with 3/8"-16 mounting hole
• Two Tilta Nucleus-M or Nucleus-M II motors and the required cables
• V-Mount or Gold Mount battery with D-Tap output for battery operation or AC power solution for Conductor SA2.6 and PTZ
• Skaarhoj controller (PTZ Fly or PTZ Extreme recommended)
  

Steps to program:

1. Power on Conductor SA2.6 and connect the Skaarhoj controller to the same wired network.
2. Use the Skaarhoj controls to frame two positions and set a preset at each one.
3. On the Skaarhoj looping page, select a loop and assign the two presets as points A and B.
4. Set the loop timing, then start and stop the loop from Skaarhoj.

For network controller configuration, see the Skaarhoj setup guide.

Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Control and keyframe Slide/Focus/Zoom
• Battery or AC operation
• Supports camera payloads up to 30 lb
• Powers and controls Tilta Nucleus-M and Nucleus-M II FIZ motors
• Control locally with the included gaming controller

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration + Rotator

What else do you need from a third party?

• RigWheels Passport 2 with track
• Flat base tripod head with 3/8"-16 mounting hole
• Two Tilta Nucleus-M or Nucleus-M II motors and the required cables
• V-Mount or Gold Mount battery with D-Tap output for battery operation or 14–16 V DC power for Camera

Steps to program:

1. Power on Conductor SA2.6 and pair the included gaming controller.
2. Use the gaming controller to position the rig and select Guided Mode, then Ping-Pong.
3. Set the start and end points using the gaming controller.
4. Set the move speed if needed, then start the shot from the gaming controller.

Features:

• Position the camera remotely or run a ping-pong AutoDolly loop
• eMotimo Rotator pans in coordination with slide to maintain framing in a loop (AutoPan)
• Motorized beltless RigWheels Passport with track sensors
• Cinematic Studio Ready
  • Live control
  • Set and recall 30 timed, cinematic presets
  • Set and recall 8 timed, cinematic loops (ping-pong)
  • Control over a wired network with Bitfocus Companion or locally with the included gaming controller
• Battery or AC operation
• Supports camera payloads up to 30 lb

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration + Rotator

What else do you need from a third party?

• RigWheels Passport 2 with track
  
• Flat base tripod head with 3/8"-16 mounting hole
  
• V-Mount or Gold Mount battery with D-Tap output for battery operation or AC power solution for Conductor SA2.6 and PTZ
• Computer with Bitfocus Companion installed
• Elgato Stream Deck XL (recommended for Bitfocus Companion)

Steps to program:

1. Power on Conductor SA2.6 and connect the computer running Bitfocus Companion to the same wired network.
2. Configure the eMotimo connection and assign live-control, preset, and loop actions through the Stream Deck.
3. Use Companion to frame two positions and set a preset at each one.
4. Use Companion’s loop actions to select those presets as the endpoints and set the move timing.
5. Start and stop the loop through the connected Stream Deck.

For network controller configuration, see the Bitfocus Companion setup guide.

Features:

• Position the camera remotely or run a ping-pong AutoDolly loop
• eMotimo Rotator pans in coordination with slide to maintain framing in a loop (AutoPan)
• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Cinematic Studio Ready
  • Live control
  • Set and recall 30 timed, cinematic presets
  • Set and recall 8 timed, cinematic loops (ping-pong)
  • Control over a wired network with Skaarhoj or locally with the included gaming controller
• Battery or AC operation
• Supports camera payloads up to 30 lb

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration + Rotator

What else do you need from a third party?

• RigWheels Passport 2 with track
  
• Flat base tripod head with 3/8"-16 mounting hole
  
• V-Mount or Gold Mount battery with D-Tap output for battery operation or AC power solution for Conductor SA2.6 and PTZ
• Skaarhoj controller (PTZ Fly or PTZ Extreme recommended)
  

Steps to program:

1. Power on Conductor SA2.6 and connect the Skaarhoj controller to the same wired network.
2. Use the Skaarhoj controls to frame two positions and set a preset at each one.
3. On the Skaarhoj looping page, select a loop and assign the two presets as points A and B.
4. Set the loop timing, then start and stop the loop from Skaarhoj.

For network controller configuration, see the Skaarhoj setup guide.

Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Control and keyframe Slide/Focus/Zoom
• Battery or AC operation
• Supports camera payloads up to 30 lb
• Control locally with the included gaming controller

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration + Rotator

What else do you need from a third party?

• RigWheels Passport 2 with track
• Flat base tripod head with 3/8"-16 mounting hole
  
• V-Mount or Gold Mount battery with D-Tap output for battery operation or 14–16 V DC power for Camera

Steps to program:

1. Power on Conductor SA2.6 and pair the included gaming controller.
2. Use the gaming controller to position the rig and select Guided Mode, then Ping-Pong.
3. Set the start and end points using the gaming controller.
4. Set the move speed if needed, then start the shot from the gaming controller.

Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Coordinated slide, pan, focus, and zoom motion
• Physical inputs for every eMotimo axis of control
• Tune live-control speed and feel for each axis, map axes to the preferred inputs, and reverse direction when needed
• Maestro automatically discovers eMotimo controllers on the same network
• Set and recall 30 timed, cinematic presets
• Set and run 8 timed, cinematic loops
• Power-on positioning gets the system ready within five minutes of startup. Saved presets and loops load automatically, so operators do not have to recreate their shots each time they power on.
• Switch between connected camera rigs from Maestro’s touchscreen or built-in Stream Deck keys
• Battery or AC operation for Conductor SA2.6
• Power and control for Tilta Nucleus-M and Nucleus-M II FIZ motors
• Camera payloads up to 30 lb

What do you need from eMotimo?

• Maestro Network Controller
• Conductor SA2.6 + RigWheels Passport/RailDolly Integration + Rotator

What else do you need from a third party?

• RigWheels Passport/RailDolly with track
• Flat base tripod head with a compatible mount
• Two Tilta Nucleus-M or Nucleus-M II motors and the required cables
• Compatible power supply for the camera
• Ethernet cabling and a network connection for Maestro and Conductor SA2.6

Steps to program:

1. Power on Conductor SA2.6 and Maestro on the same network. Maestro discovers the controller automatically.
2. Select the rig on Maestro. Use its physical inputs to frame the shot and adjust axis mapping, speed, and feel.
3. Save the start and end positions as timed presets.
4. Create a loop between those presets and set its move timing.
5. Start and stop the loop from Maestro’s built-in Stream Deck keys.

At the next startup, power-on positioning restores the saved setup and gets the rig ready within five minutes.

Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Coordinated slide and pan motion
• Physical inputs for every eMotimo axis of control
• Tune live-control speed and feel for each axis, map axes to the preferred inputs, and reverse direction when needed
• Maestro automatically discovers eMotimo controllers on the same network
• Set and recall 30 timed, cinematic presets
• Set and run 8 timed, cinematic loops
• Power-on positioning gets the system ready within five minutes of startup. Saved presets and loops load automatically, so operators do not have to recreate their shots each time they power on.
• Switch between connected camera rigs from Maestro’s touchscreen or built-in Stream Deck keys
• Battery or AC operation for Conductor SA2.6
• Camera payloads up to 30 lb

What do you need from eMotimo?

• Maestro Network Controller
• Conductor SA2.6 + RigWheels Passport/RailDolly Integration + Rotator

What else do you need from a third party?

• RigWheels Passport/RailDolly with track
• Flat base tripod head with a compatible mount
• Compatible power supply for the camera
• Ethernet cabling and a network connection for Maestro and Conductor SA2.6

Steps to program:

1. Power on Conductor SA2.6 and Maestro on the same network. Maestro discovers the controller automatically.
2. Select the rig on Maestro. Use its physical inputs to frame the shot and adjust axis mapping, speed, and feel.
3. Save the start and end positions as timed presets.
4. Create a loop between those presets and set its move timing.
5. Start and stop the loop from Maestro’s built-in Stream Deck keys.

At the next startup, power-on positioning restores the saved setup and gets the rig ready within five minutes.