Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Coordinated pan, tilt, roll, slide, focus, and zoom motion
• Physical inputs for every eMotimo axis of control
• Tune live-control speed and feel for each axis, map axes to the preferred inputs, and reverse direction when needed
• Maestro automatically discovers eMotimo controllers on the same network
• Set and recall 30 timed, cinematic presets
• Set and run 8 timed, cinematic loops
• Power-on positioning gets the system ready within five minutes of startup. Saved presets and loops load automatically, so operators do not have to recreate their shots each time they power on.
• Switch between connected camera rigs from Maestro’s touchscreen or built-in Stream Deck keys
• Battery or AC operation for Conductor SA2.6
• DJI RS gimbal control with camera payloads up to 10 lb (gimbal limited)
• Power and control for Tilta Nucleus-M and Nucleus-M II FIZ motors

What do you need from eMotimo?

• Maestro Network Controller
• Conductor SA2.6 + RigWheels Passport/RailDolly Integration

What else do you need from a third party?

• RigWheels Passport/RailDolly with track
• Compatible DJI RS gimbal and its power base
• Two Tilta Nucleus-M or Nucleus-M II motors and the required cables
• Battery with D-Tap output or a compatible DC supply for the gimbal/camera
• Ethernet cabling and a network connection for Maestro and Conductor SA2.6

Steps to program:

1. Power on Conductor SA2.6 and Maestro on the same network. Maestro discovers the controller automatically.
2. Select the rig on Maestro. Use its physical inputs to frame the shot and adjust axis mapping, speed, and feel.
3. Save the start and end positions as timed presets.
4. Create a loop between those presets and set its move timing.
5. Start and stop the loop from Maestro’s built-in Stream Deck keys.

At the next startup, power-on positioning restores the saved setup and gets the rig ready within five minutes.

Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• pan, tilt, roll, slide, focus, and zoom move together in coordinated shots
• Cinematic Studio Ready
  • Live control
  • Set and recall 30 timed, cinematic presets
  • Set and recall 8 timed, cinematic loops (ping-pong)
  • Control over a wired network with Bitfocus Companion or locally with the included gaming controller
• Battery or AC operation
• Supports camera payloads up to 10 lb (RS Gimbal Limited)
• Controls DJI RS2/3/4 Pro gimbal
• Powers and controls Tilta Nucleus-M and Nucleus-M II FIZ motors

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration
  

What else do you need from a third party?

• RigWheels Passport 2 with track
• Two Tilta Nucleus-M or Nucleus-M II motors and the required cables
• DJI RS 4 Pro Gimbal (RS 2, 2 Pro, 3, 3 Pro, 4, and 4 Pro supported)
  
• Power Base for Gimbal (we recommend SmallRig Power Supply Base Plate for DJI RS)
• V-Mount or Gold Mount battery with D-Tap output for battery operation or 14–16 V DC power for Gimbal/Camera
• Computer with Bitfocus Companion installed
• Elgato Stream Deck XL (recommended for Bitfocus Companion)

Steps to program:

1. Power on Conductor SA2.6 and connect the computer running Bitfocus Companion to the same wired network.
2. Configure the eMotimo connection and assign live-control, preset, and loop actions through the Stream Deck.
3. Use Companion to frame two positions and set a preset at each one.
4. Use Companion’s loop actions to select those presets as the endpoints and set the move timing.
5. Start and stop the loop through the connected Stream Deck.

For network controller configuration, see the Bitfocus Companion setup guide.

For network controller configuration, see the Skaarhoj setup guide.

Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• pan, tilt, roll, slide, focus, and zoom move together in coordinated shots
• Cinematic Studio Ready
  • Live control
  • Set and recall 30 timed, cinematic presets
  • Set and recall 8 timed, cinematic loops (ping-pong)
• Battery or AC operation
• Supports camera payloads up to 10 lb (RS Gimbal Limited)
• Controls DJI RS2/3/4 Pro gimbal
• Powers and controls Tilta Nucleus-M and Nucleus-M II FIZ motors
• Control locally with the included gaming controller

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration
  

What else do you need from a third party?

• RigWheels Passport 2 with track
• Two Tilta Nucleus-M or Nucleus-M II motors and the required cables
• DJI RS 4 Pro Gimbal (RS 2, 2 Pro, 3, 3 Pro, 4, and 4 Pro supported)
• Power Base for Gimbal (we recommend SmallRig Power Supply Base Plate for DJI RS)
• V-Mount or Gold Mount battery with D-Tap output for battery operation or 14–16 V DC power for Gimbal/Camera

Steps to program:

1. Power on Conductor SA2.6 and pair the included gaming controller.
2. Use the gaming controller to position the rig and select Guided Mode, then Ping-Pong.
3. Set the start and end points using the gaming controller.
4. Set the move speed if needed, then start the shot from the gaming controller.

Features:

• Position the PTZ camera remotely or run a ping-pong AutoDolly loop
• Motorized beltless RigWheels Passport with track sensors
• Cinematic Studio Ready
  • Live control
  • Set and recall 30 timed, cinematic presets
  • Set and recall 8 timed, cinematic loops (ping-pong)
  • Control over a wired network with Bitfocus Companion or locally with the included gaming controller
• Wall power for Conductor SA2.6 and the PTZ camera

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration
  
• Riser with Clamp and 100mm Arca Plate (recommended for mounting PTZ to eMotimo Rotator)
  • Riser with Clamp
  • 100mm Arca Plate

What else do you need from a third party?

• RigWheels Passport 2 with track
• PTZ camera of your choice
• Computer with Bitfocus Companion installed
• Elgato Stream Deck XL (recommended for Bitfocus Companion)
• Wall power for Conductor SA2.6 and the PTZ camera (Conductor AC adapter included with the bundle; use the camera’s compatible AC supply)

Steps to program:

1. Power on Conductor SA2.6 and connect the computer running Bitfocus Companion to the same wired network.
2. Configure the eMotimo connection and assign live-control, preset, and loop actions through the Stream Deck.
3. Use Companion to frame two positions and set a preset at each one.
4. Use Companion’s loop actions to select those presets as the endpoints and set the move timing.
5. Start and stop the loop through the connected Stream Deck.

For network controller configuration, see the Bitfocus Companion setup guide.

For network controller configuration, see the Skaarhoj setup guide.

Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Control and keyframe Slide/Focus/Zoom
• Battery or AC operation
• Supports camera payloads up to 30 lb
• Powers and controls Tilta Nucleus-M and Nucleus-M II FIZ motors
• Control locally with the included gaming controller

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration
  

What else do you need from a third party?

• RigWheels Passport 2 with track
• Two Tilta Nucleus-M or Nucleus-M II motors and the required cables
• Tripod head with compatible mounting adapter to RigWheels Passport
• V-Mount or Gold Mount battery with D-Tap output for battery operation or 14–16 V DC power for Camera

Steps to program:

1. Power on Conductor SA2.6 and pair the included gaming controller.
2. Use the gaming controller to position the rig and select Guided Mode, then Ping-Pong.
3. Set the start and end points using the gaming controller.
4. Set the move speed if needed, then start the shot from the gaming controller.

Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Control and keyframe Slide
• Battery or AC operation
• Supports camera payloads up to 30 lb
• Control locally with the included gaming controller

What do you need from eMotimo?

• Conductor SA2.6 + RigWheels Passport/RailDolly Integration
  

What else do you need from a third party?

• RigWheels Passport 2 with track
  
• Tripod head with compatible mounting adapter to RigWheels Passport
• V-Mount or Gold Mount battery with D-Tap output for battery operation or 14–16 V DC power for Camera

Steps to program:

1. Power on Conductor SA2.6 and pair the included gaming controller.
2. Use the gaming controller to position the rig and select Guided Mode, then Ping-Pong.
3. Set the start and end points using the gaming controller.
4. Set the move speed if needed, then start the shot from the gaming controller.

Features:

• Motorized beltless RigWheels Passport/RailDolly with track sensors
• Live control of camera travel along the track
• Physical inputs for every eMotimo axis of control
• Tune live-control speed and feel for each axis, map axes to the preferred inputs, and reverse direction when needed
• Maestro automatically discovers eMotimo controllers on the same network
• Set and recall 30 timed, cinematic presets
• Set and run 8 timed, cinematic loops
• Power-on positioning gets the system ready within five minutes of startup. Saved presets and loops load automatically, so operators do not have to recreate their shots each time they power on.
• Switch between connected camera rigs from Maestro’s touchscreen or built-in Stream Deck keys
• Wall power for Conductor SA2.6 and the PTZ camera

What do you need from eMotimo?

• Maestro Network Controller
• Conductor SA2.6 + RigWheels Passport/RailDolly Integration
• Riser with Clamp and 100 mm Arca Plate (recommended for mounting the PTZ camera)

What else do you need from a third party?

• RigWheels Passport/RailDolly with track
• PTZ camera of your choice
• Ethernet cabling and a network connection for Maestro and Conductor SA2.6
• Wall power for Conductor SA2.6 and the PTZ camera (Conductor AC adapter included with the bundle; use the camera’s compatible AC supply)

Steps to program:

1. Power on Conductor SA2.6 and Maestro on the same network. Maestro discovers the controller automatically.
2. Select the rig on Maestro. Use its physical inputs to frame the shot and adjust axis mapping, speed, and feel.
3. Save the start and end positions as timed presets.
4. Create a loop between those presets and set its move timing.
5. Start and stop the loop from Maestro’s built-in Stream Deck keys.

At the next startup, power-on positioning restores the saved setup and gets the rig ready within five minutes.