May 13, 2025
by Brian Burling

JL Fisher BBQ

May 13, 2025
by Brian Burling

Thanks for stopping on by to see us at the JL Fisher BBQ. We exhibited at the Hot Rod Camera booth on the corner and were showing off our:

Conductor SA2.6 motion controller, with our very new beltless Dana Dolly Integration kit, on curved track from American Grip (Thanks Lance and team).

It was nice to be out and chatting with industry folks and eating too much amazing food. Thanks for hosting JL Fisher folks!

If you stopped by and chatted with us at the corner booth, you likely spoke with Brian or Max and got your hands on the gaming controller to set up a very easy ping-pong interview shot. Even if it was your first time, setting up a shot in a minute or less was pretty standard. Once you learned how to control the panning, tilting, sliding, zooming shot - and setup basic start and end point, you were off and running!

Please peruse the solutions below and let us know what might work for you. We hope to have you as an ecstatic customer very soon. If you have any question, reach out to us by sending and email (sales@emotimo.com) or giving us a call 415-684-8162 and leave a message.

- Brian (eMotimo founder guy)

Dana Dolly V3 Integration Kits

Conductor SA2.6 w/ RSI and Dana Dolly V3 Beltless Kit

$1,899.00

If you have a compatible DJI Gimbal (RS2, RS3, and RS4) and an unmotorized Dana Dolly, this kit adds eMotimo's Dana Dolly integration.

Conductor SA2.6 Motion Controller
RSI + 6Pin RSI Cable (DJI RS2/RS3/RS4 integration dongle and cable)
PS5 Dual Sense Remote
DTAP to 2.1mm locking power cable
12VDC 2.0A Wall Supply
MicroSD card for firmware updates
Dana Dolly Beltless Integration Kit

Buy now - $1,899.00

Dana Dolly Beltless Integration V3 with Conductor SA2.6 Track Sensor

$489.00

For existing Conductor SA2.6 users, this kit includes:

Motor Pod with 21" cable (plugs into M1 port on SA2.6)
Track Sensor

Buy now - $489.00

Dana Dolly Beltless Integration V3 with Spectrum ST4/ST4.3 Track Sensor (Presale)

$499.00

Ships on or before August 15

For existing Spectrum ST4/ST4.3 users, this kit includes:

Motor Pod with 21" cable (plugs into M3 port on ST4/4.3)
Powered i/o port dongle for Spectrum ST4/4.3
Track Sensor
**Please note: The DDV3 track sensor plugs into the same i/o port on the ST4/ST4.3 as the network adapter. DDV3 track sensor and network adapter cannot be used concurrently on ST4/ST4.3**

Buy now - $499.00

See what you can do with Conductor and DDV3

View all

AutoDolly AutoPan Conductor SA2.6 infocomm Passport PTZ RigWheels

SA26-6 Passport PTZ Mover with AutoPan

Solution: SA26-6 RigWheels Passport PTZ Mover with AutoPan - Coming Soon! Summary Take your high-end PTZ and make it dynamic by putting in on a dolly. Add in our autopan axis which physically rotates the PTZ to add in counterpan...

Conductor SA2.6 infocomm Monorail RigWheels

SA26-5 Monorail + Conductor - Long Runs, Easy Rigging

The Monorail is one of the most innovative new ways to move small to medium cameras. It support ping-pong automation shots, cinematic and timed presets, and live control. It has a single rail for support that can extend indefinitely (with middle hanger supports every 10 feet) in positions where other linear solutions can't go. It support cameras up to 10lbs mounted on DJI RS gimbals. The entire solution (Pan/Tilt/Roll/Slide/Focus/Zoom) is controlled and coordinated by eMotimo's Conductor SA2.6 motion controller. You can control it locally with a gaming remote, or from the control room when connected to a wired network.

infocomm Passport RigWheels spectrum ST4

ST43-5 Spectrum + Passport Dolly + Focus Zoom

Connect your eMotimo spectrum ST4.3 motion control head to Passport2 /RailDolly2 Sliders for live control, loops, and preset recall with mid-sized cinema cameras. All motors are powered and controlled from the ST4.3 motion control head and controller. Great for front of stage or back of house applications where you support comes from the floor or stands.